Craftsman 113.198611 Operators Manuale dell'Operatore Pagina 77
- Pagina / 120
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Featherboard
Featherboards are used during rip cutting to
help keep the workpiece against the fence.
The featherboard is clamped to the front
table, so that the angled edge of the feather-
board is against the workpiece on the infeed
end of the blade. The other edge of the
workpiece is against the fence.
Make new featherboards when existing ones
have been damaged.
1. Use solid (knot free) lumber 24 inches by
5 1/2 inches by 3/4 inch.
2. On the 24 inch sides mark a point 5 1/2 in-
ches down on the left and 9 1/2 inches down
on the right from the edge of the board.
Draw a line between the points.
3.Crosscut workpiece at a 30 ° angle then rip
to make the kerfs.
4. Do not clamp the featherboard against the
cut off part of the workpiece.
Note: All Dimensions in Inches
F;ff. 169 Featherboard Dimensions
Attaching Auxiliary Board to
Crooked Workpiece
If the workpiece you want to rip cut does not
have a straight edge, attach an auxiliary board
to the workpiece.
1. Place irregular side of workpiece against
fence.
2. Place straight edged auxilia U board on top
of workpiece and against fence.
3. Tack the auxilia U board to the workpiece.
The atLxiliary board must not extend beyond
the leading end of the workpiece and should
cover the workpiece width only enough to
pass between the blade and fence.
3. Use a fence that is equal to or higher than
the combined height of the workpiece and
auxiliary board.
77
- CRRFTSMRN 1
- Table of Contents 2
- Safety Information 3
- Personal Safety 5
- Work Area Safety 5
- I DANGER I 6
- Putting Your Saw Together 7
- Information 10
- Model 113.198611 11
- _r Bracket 12
- Smooth Pin In Groove 14
- H S°r'a e 15
- Model 113.198411 19
- Long End Of Shelf 20
- Right Side Panel 21
- , Upper Support 23
- Mounting the Motor 25
- Mounting the Saw 26
- Mounting Table Locks 27
- Mounting the Front Table 28
- I Holes o \ 29
- Putting Drawers in Place 30
- Removing Drawers 30
- On/Off Switch 31
- Bevel Lock 32
- Swivel Lock 33
- Rip Lock 33
- All Controls 34
- Alignment of the Blade 35
- Leveling Front Table 36
- Fig. 101 37
- Fig. 100 37
- Adjusting Table Locks 38
- Squaring Crosscut Travel 39
- Squaring Blade to Table for 41
- Crosscutting 41
- Squaring Blade to Fence 42
- Square Squa 43
- 6. Unlock the swivel lock 43
- Fig. 113 43
- Fig. 118 45
- Making Blade Parallel to 46
- Installing Guard / Setting 47
- Spreader 47
- _A/RS / CRI1FT$1dRN 50
- ELECTRONIC MEASUREMENT 50
- Installing the Battery 51
- [ °._qc, 52
- I q,-,,-,I 53
- Setting Zero References 54
- 1 '-"-'I 55
- Electrical Connections 56
- Extension Cords 57
- Safety Information for 59
- Blade Guard, Anti-Kickback 60
- Pawls and Spreader 60
- Crosscut Checklist 61
- Wear safety 62
- Making Crosscuts 63
- Repetitive Crosscuts 64
- Saw Positions for Ripping 65
- Rip Cutting Checklist 68
- Making a Rip Cut Table Kerf 69
- Adjustments for Ripping 69
- Making Rip Cuts 70
- 13. Turn the saw off 72
- Fig. 160 Edging Label 73
- Accessory Safety 73
- Cutting Accessories 74
- Auxiliary Fence and Push 75
- .o.e:A,,O. oosions,:,nohe 76
- Featherboard 77
- *Recommended Accessories 78
- Glossary 79
- Helpful Hints 80
- Decimal Equivalent 81
- Maintaining Your Saw 82
- Column Tube 83
- Fig. 176 - Collapsed Bellows 83
- Adjustments for Wear 84
- Manual Reset Button 88
- Changing Motor Voltage 89
- Troubleshooting 90
- Electronics - 2 91
- Motor - 2 92
- Saw Operations 93
- Saw Operations - 2 94
- Saw Operations - 3 95
- Figure 1 96
- FIGURE 1 97
- Figure 2 98
- Figure 3 100
- FIGURE 5 - ARM ASSEMBLY 105
- FIGURE 6 - TABLE ASSEMBLY 106
- Description 107
- Figure 8 108
- Figure 9 110
- FIGURE 11 - MOTOR ASSEMBLY 113
- FIGURE 12 - GUARD ASSEMBLY 114
- SEA/R 120
Prodotti e manuali riguardandi Sega circolare Craftsman 113.198611 Operators
(20 pagine)
(62 pagine)Canon PowerShot N manuels
Manuels d'utilisation et guides de l'utilisateur pour Non Canon PowerShot N.
Nous fournissons des manuels en pdf 4 Canon PowerShot N à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commenti su questo manuale